Determination of parameters of the primary mode of the tunung fork type solid-state gyroscope
DOI:
https://doi.org/10.17721/1812-5409.2021/4.13Ключові слова:
вібраційний гіроскоп, камертонний п’єзоперетворювач, резонансні коливанняАнотація
The use of a tuning fork resonator as sensitive element of a gyroscopic sensor has some advantages in comparison with other types of the resonators. For instance, it allows to compensate lateral accelerations in the direction perpendicular to the axis of rotation. At the same time, the task of accurate determination of the carrying frequency of the primary mode of a non-moving tuning fork is of great importance. Thus, in [1] the analysis of vibrations of a gyroscope is built on the evaluation of the first frequency of flexure vibrations of Timoshenko's beam with one rigidly fixed end [2]. As a result, the sensing frequencies of the Bryan's splitting pair [3] of the fork lie below the frequency of Timoshenko's beam, and the resonant frequency of the non-moving tuning fork remained uncertain. The purpose of a present paper is to establish this frequency. In the statement of a problem, concerning real geometric dimensions of the tuning fork elements, we assume that the length of the tuning fork rods l is much more then the radius of the base r: r/l << 1. Then, frequencies of the flexure vibrations of the half-ring lie much higher than the frequencies of the bending vibrations of the rods. It allows us to give a solution for the base in a quasi-static approximation, and to take into account the dynamics of the tuning fork in the solution for bimorph piezoceramic rods. Conditions of coupling between the rods and the half-ring are reduced to the conditions of elastic fixing of the rods, which take into account the geometric parameters r and l.
Pages of the article in the issue: 82 - 87
Language of the article: Ukrainian
Посилання
ULITKO, I. A. (1995) Mathematical theory of the fork-type wave gyroscope. In: Proc 1995 IEEE Int. Frequency Control Symposium. San Francisco, USA pp. 786–793.
TIMOSHENKO, S., YOUNG, D.H., WEAVER, W. (1974) Vibration problems in engineering. John Willey & Sons.
BRYAN, G.H. (1890) On the beats in the vibrations of a revolving cylinder or bell. Proc. Cambridge Phil. Soc. Math. Phys. Sci. 7. pp. 101–111.
GRINCHENKO, V.T., ULITKO, A.F., SHULGA, N.A. (1989) Electroelasticity. Naukova Dumka
ULITKO, I. A. BORISEIKO, O.V. (2019) Sensorny signal vibratsiynogo piezogyroscopy kamertonnogo typu. In: Proc XIX Int. Conf. Dynamical Systems Modeling and Stability Investigation (DSMSI-2019) 22-24 May 2019, Кyiv. pp. 284-286.
FRIEDT, J.M., CARRY, É. (2007) Introduction to the quartz tuning fork American Journ. Physics. 75(5) pp. 415-422.
FAN, M., ZHANG, L. (2015) Research progress of quartz tuning fork micromachined gyroscope In: Int. Conf. on Artifical Intelligence & Industrial Engineering, AIIE 2015, July 26-27, 2015, Phuket, Thailand: pp. 361-364.
Завантаження
Опубліковано
Номер
Розділ
Ліцензія
Автори, роботи яких публікуються у цьому журналі, погоджуються з такими умовами:
- Автори зберігають авторські права та надають журналу право на першу публікацію роботи, яка одночасно ліцензується згідно із Creative Commons Attribution License, тобто надається дозвіл іншим ділитися роботою з визнанням авторства роботи та першої публікації в цьому журналі.
- Автори можуть укладати окремі додаткові угоди щодо невиключного розповсюдження опублікованої журналом версії роботи (наприклад, розмістити її у репозитарії наукової установи чи опублікувати у книзі) з підтвердженням її початкової публікації у цьому журналі.
- Дозволяється та заохочується розміщення своїх робіт в мережі Інтернет авторами (наприклад, у репозитаріях наукових установ або на особистих веб-сторінках) до та під час процесу подання, оскільки це може призвести до продуктивного обміну, а також до більш ранніх цитувань опублікованої роботи та їх більшої кількості (див. The Effect of Open Access).
