Physico-mechanical characteristics of nanocomposite materials based on fluoroplastic
DOI:
https://doi.org/10.17721/1812-5409.2021/3.20Keywords:
nanocomposite material, microhardness, polytrifluorochloroethylene, expanded graphiteAbstract
In this work, the elastic and strength properties of polymer composites with a polytrifluorochlorethylene matrix and a thermally expanded graphite filler were evaluated by the nanoindentation method, and the effect of the dispersion and concentration of the filler on the mechanical characteristics of nanocomposite materials was considered. It is shown that the microhardness of nanocomposite materials decreases with increasing filler concentration. An increase in the microhardness and Young's modulus with the growth of filler particles was observed for nanocomposite materials with a filler concentration of 3 vol.%. As for nanocomposite materials with a filler volume fraction of 10 vol.%, similar behavior of the mechanical characteristics was observed with an increase in the dispersion of thermally expanded graphite particles to 180 ?m. A subsequent increase in the average particle size of thermally expanded graphite leads to a decrease in Young's modulus and microhardness of composites, which may be associated with different degrees of polymer structuring and the formation of different orientational orders from the filler. The observed changes in Young's modulus and H/E ratio indicate a change in the amorphous crystalline behavior of the composite to that characteristic of fine-crystalline materials and depends on the dispersion of thermally expanded graphite.
Pages of the article in the issue: 107 - 110
Language of the article: Ukrainian
References
JOSE J.P., THOMAS S., KURUVILLA J., MALHOTRA S.K., GODA K., M.S. SREEKALA M.S. (2012) Advances in polymer composites: Macro- and microcomposites—State of the art, new challenges, and opportunities. Polymer Composites, Wiley. 1. pp. 3–16.
MASUELLI M.A. (2013) Introduction of fibre-reinforced polymers–Polymers and composites: Concepts, properties and processes. Fiber Reinforced Polymers–The Technology Applied for Concrete Repair; M. Masuelli, Ed. p. 39.
LIN S., ANWER M.A.S., ZHOU Y., SINHA A., CARSON L., NAGUIB H. (2018) Evaluation of the thermal, mechanical and dynamic mechanical characteristics of modified graphite nanoplatelets and graphene oxide high-density polyethylene composites. Composites Part B: Engineering. 132. pp. 61–68.
SEMENTSOV YU.I., REVO S.L., IVANENKO K.O. (2016) Thermally exfoliated graphite. Kyiv: Interservis.
PANDA A., DYADYURA K., VAL͡CEK J., HARNIˇCÁROV M., ZAJAC J., MODRÁ V., PANDOV I., VRÁBEL P., NOVÁKOVÁ-MARCINˇCÍNOV E. AND PAVELEK Z. (2017) Manufacturing Technology of Composite Materials–Principles of Modification of Polymer Composite Materials Technology Based on Polytetrafluoroethylene. Materials. 10(4). p. 377.
Downloads
Published
Issue
Section
License
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
